Skip to the stories
Microsoft 365 & SharePoint

Elastomer Seals and the Contamination Gap in Direct-to-Chip Cooling

  • Natalie Stipan
  • 994 views

Seal qualification covers compound chemistry but ignores surface debris, which can shed into microchannels that have very little thermal margin left.

Elastomer Seals and the Contamination Gap in Direct-to-Chip Cooling

Walk through a modern direct-to-chip cooling loop and list every wetted material that has a published specification. The list is long: the cold plate base, the surface finish, the joining method, the coolant chemistry, the flatness of the contact face, and the leak test regime. Then look at the elastomer seals. In most cases you'll find compound qualification data and not much else. That gap matters more than most teams realize, and according to Bill Sharratt, President of Pacific Rubber & Packing, it's where the next round of thermal problems is likely to start.

What the specifications leave out

The cold plate side of the loop is well documented. Sharratt describes typical C11000 electrolytic copper bases with a thermal conductivity floor, electroless nickel plating at five to eight microns to resist galvanic attack, and vacuum brazing with a documented burst pressure. Helium leak testing to better than 10⁻⁸ mbar·L/s is applied to every unit, followed by pressure testing at twice operating pressure. Coolant glycol fraction, pH band and inhibitor package are all defined.

Elastomer seals are specified too, and the compound side has been characterized thoroughly. Compatibility with PG25, dielectric immersion fluids and two-phase refrigerants has been tested for extractables, swell, hardness drift and thermal aging. Sharratt's point is that this work is sound, and material qualification isn't the problem. The problem is that none of it describes the part that arrives at the receiving dock.

A seal typically passes three checks before it enters a loop: material qualification for coolant compatibility, incoming inspection for gross defects such as excess flash and dimensional errors, and the loop's filtration rating. None of the three examines what is sitting on the surface.

What's actually on the part

Sharratt's team examined seals across materials and manufacturers and sorted the surface contamination into three groups. Each needs a different removal method:

  • Insoluble particulate, including dirt, dust and carbon black
  • Oils and release films left by molding and by handling
  • Living bioburden, including bacteria and fungal spores

Much of this comes from processing rather than the polymer itself. Deflashing tumbles molded parts against silica and abrasive media, which can leave fine grit embedded in the surface. Carbon black builds up through processing, and the load grows at each step. Then the part gets handled.

The harder problem is variance. Sharratt notes that cleaner and dirtier material lots exist, but the spread across lots, bags and manufacturers is wide. Within one bag, the cleanest and dirtiest seals can differ by several times. That means choosing a compound or auditing a supplier doesn't control the outcome. Qualification describes the compound, but contamination behaves like a distribution, and it's the tail of that distribution that ends up in a channel.

Why the margin is so thin

Here's the thing: the thermal budget no longer has room for a deposit. Sharratt cites published design guidance for current cold plates that puts the junction-to-coolant thermal resistance budget near 0.030 °C/W, with production units landing between 0.026 and 0.029. That leaves 10 percent margin or less, against GPU thermal design power now measured in thousands of watts per device. Any film on a channel wall adds series resistance straight into that budget. Channel geometry is also shrinking, from roughly 200 microns toward 100, which halves the gap available to the same particle.

The effect is less obvious than a simple blockage. These cold plates split flow across dozens of parallel sub-millimeter channels under a tightly limited pressure drop. Flow takes the path of least resistance, so a partly obstructed channel doesn't just get a little hotter. Its flow is diverted to its neighbors, it starves, its wall temperature rises, and deposition speeds up in the channel that can least tolerate it. Operators see intermittent thermal excursions rather than a clean fault, and those can show up months after commissioning with no obvious cause.

Why the commissioning flush isn't enough

The usual reassurance is that the commissioning flush removes contamination. Sharratt's argument is that it can't, and the reason is mechanical. A seal is designed not to fill its gland completely, because an overfilled seal extrudes and fails. That leaves room for movement. Each pressurization cycle shifts and rotates the seal inside the gland, exposing surface that the initial flush never wetted. He calls this cyclic contamination displacement. The loop keeps picking up new debris well after handover.

Filtration is the other gap

Filters don't close the loop either. Sharratt says a meaningful share of seal-borne particulate is small enough to pass typical loop filter ratings. Once through, it can foul a microchannel or gradually agglomerate. On the facility side, he describes filtration that is often no finer than a 35 to 40 mesh strainer, roughly 400 to 500 microns. Larger particles that a filter does catch shorten filter life and add maintenance work.

The reference point many teams use is ASHRAE's Liquid Cooling Guidelines for Datacom Equipment Centers, second edition, published in 2014. It calls for filtering particles of 10 microns and larger "or at a minimum of the smallest passage in the system." That guidance predates 120 kW racks and today's channel geometry. Sharratt also notes that the Open Compute Project's cold plate documents address fluids, leak detection and serviceability, but not the cleanliness of wetted non-metallic parts.

What a cleanliness spec could look like

Sharratt argues this isn't new engineering. Semiconductor fabs qualify wetted elastomers for particle shedding as routine practice, because one stray particle can scrap a wafer. The measurement methods and protocols already exist, and the cooling industry hasn't asked for them yet.

What he proposes is an incoming cleanliness standard for seals, structured like ISO cleanroom classifications. It would define absolute particle counts at specified sizes and apply across materials, manufacturers and geometries. An engineer would pick the class the application requires, then work backward to the material, supplier and cleaning process that can meet it.

If you own a liquid cooling loop or buy the parts for one, the practical step is to start asking suppliers questions the datasheet doesn't answer. What is the particle count on arrival? How are parts cleaned after deflashing? What contamination control applies during packaging and handling? Those answers will show you where your exposure sits before a thermal excursion does.

Source: Natalie Stipan · datacenterpost.com

Neighbouring cells